However, the thin wrenches were said to be delicate and broke easily. Positive reviews mentioned that the set had a variety of wrenches and the common sizes, which tend to be the ones in the middle, were durable and didn’t bend or snap under pressure. Additionally, the wrenches come in a hinged storage case that opens flat, making it easier to access the wrenches. This set comes with 15 short-arm wrenches measured in millimeters and 15 long-arm wrenches measured in inches, giving you enough wrench sizes and arm length options to fit multiple screw types. The wrenches in this set performed well, but we deducted a point from the set’s case ergonomics score because of how difficult they were to get out of the case. The wrenches were also able to loosen a tight screw without a problem. The wrenches in this set had ball ends like the wrenches in the first set, which helped with reaching a screw on the underside of a piece of furniture. All three were able to loosen and tighten screws on the piece of furniture we ordered. Similar to the previous set, we tested three wrenches of different sizes from this set. The set’s case did a good job of keeping the wrenches in place, but the rubber around the wrenches was extremely tight, making it difficult to pull them out when we needed to use them. However, some customers felt like the set skipped a few wrench sizes, making it impossible to loosen all of the screws they came across. When trying to loosen an extra tight screw, the wrenches didn’t strip the screw or snap, unlike competing products made in China. Key FeaturesĬustomers were pleased with the quality of the wrenches. The ball ends on the longer arms allow you to come at a fastener at an angle, which is useful for hard-to-reach screws like those on the underside of a piece of furniture. The wrenches in this set have both straight and ball ends. This set ticked all of the boxes in terms of what you need out of the wrenches and case, so we gave it full points across the board. The ball-end of the screws was especially useful when loosening the latter screw because we were able to come at the screw at an angle instead of straight on. The wrenches were able to loosen an extra tight screw and a screw on the underside of a piece of furniture. Regarding performance, we tried three wrenches in the set and none of them had issues with loosening or tightening screws. The holes in the rubber fit the wrenches perfectly, and we liked how the front row of the case swung open because that made it easier to pull out a wrench. This set’s case kept the wrenches in place and made them easy to access. However, some customers said that the wrenches only had a 10-degree entry angle instead of the 25 degrees like TEKTON advertised. Key FeaturesĬustomers liked how the wrenches in this set had ball ends and how they could reach any screw because they could come in at an angle and the ball-end would fit into the screw. Additionally, these wrenches have a black oxide finish that protects against corrosion and color-coded housing for instant identification. The holes perfectly fit each wrench and you can swing open the case to pull out the wrench you need. It took about 1-1/2 hours to fix the saw.The case for this set keeps your wrenches in place and makes it easy to pull out a particular size. The noise doesn't last long, if it does continue Milwaukee said to disassemble and reassemble the saw, looking for any bushings or spacers that may have fallen out of place. When the saw is complete and you go to test the saw it will make a funny sound? can't explain it, only know that it will go away, when I asked Milwaukee they said the parts were seating themselves. If you over tighten them you'll know it and you will have to buy some lock tight. Everything fits back together rather snug, so don't force anything, and don't over tighten the torx screws. If this happens, be aware that there is a small spacer for the armature that sits down with the brushes, just be mindful that it needs to go back, if you don't put it back the drill won't work properly. Take caution, the armature will want to pull out when disassembling the gear housing. I did this with a 6mm socket and a bench vise. There is a bearing for the transfer gear that needs to be removed from the old gear housing and installed into the new one before you reassemble the saw. Unit case and blade guard need to be removed before the gear housing can be accessed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |